manualshive.com logo in svg

Axis AXIS 570, User Manual

Share
Download
Axis AXIS 570 User Manual Download Page 89

 

AXIS 5470e/570/670e

 

User’s Manual

 Section 5: Setting Up - IBM Mainframe

 

89

 

PPR/PPD Printing - IPDS data streams

Note:

Before you begin

In order to use the AXIS 5470e/570/670e to print IPDS data using 
TCP/IP as the transport protocol, the following software must be 
installed and configured on your MVS:

•

PSF/MVS Version 2 release 2.0 with APAR OW15599.

•

MVS Scheduler APAR OW12236 to support the two new

PRINTDEV

 keywords: 

IPADDR

 and 

PORTNO

.

•

TCP/IP version 3 release 1, or higher

As the AXIS 5470e/570/670e translates IPDS to PostScript, you also 
need a printer with PostScript level 2 capability.

Configuration

Procedures

The configuration procedures presented in this section are divided 
into seven separate steps:

1. Specifying the TCP/IP address space name

2. Defining the MVS control unit

3. Modifying the TCP/IP profile on your MVS system, if necessary

4. Configuring the AXIS 5470e/570/670e

5. Verifying the communication between the AXIS 5470e/570/670e 

and the IBM Mainframe

6. Defining the AXIS 5470e/570/670e as a writer-controlled printer 

to JES

7. Defining the printer to PSF with a 

PRINTDEV

 statement, 

including the IP address and port number.

IPDS is only available for AXIS 670e and AXIS 5470e units with the IPDS option 
installed. Please refer to 

Product Model Summary

 on page 10.

Summary of Contents for AXIS 570





























































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands