manualshive.com logo in svg

Axis AXIS 570, User Manual

Share
Download
Axis AXIS 570 User Manual Download Page 93

 

AXIS 5470e/570/670e

 

User’s Manual

 Section 5: Setting Up - IBM Mainframe

 

93

 

Configuring the

AXIS 5470e/570/670e

Follow the instructions below to configure your AXIS 
5470e/570/670e using a standard Web browser:

1. Start a Web browser, e.g. Internet Explorer or Netscape Navigator.

2. Enter the IP address or the host name of the AXIS 

5470e/570/670e in the location field and press the 

Enter

 key on 

your keyboard. The internal Web pages of the AXIS 
5470e/570/670e will appear. 

Note

:

3. Click the 

Configuration Wizard for IBM sessions 

button.

 

4. Click the 

Add Session

 button. This will start the 

Configuration 

Wizard

 which is a step-by-step guide through the required IBM 

configuration settings.

Verifying the

communication

You can verify the communication between the MVS system and the 
AXIS 5470e/570/670e by pinging the print server from the MVS 
system. A successful ping indicates that the MVS system can 
communicate with the AXIS 5470e/570/670e.

To protect the 

admin

 pages and the 

Configuration Wizard

 from unauthorized 

use, enter a password (default Pass) in the 

Root Password

 field under 

admin | 

General Settings

. 

Summary of Contents for AXIS 570





























































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands