manualshive.com logo in svg

Axis AXIS 570, User Manual

The user manual for the high-performance Axis AXIS 570 is available for free download at manualshive.com. This comprehensive manual provides detailed instructions and information on operating and optimizing the features of this exceptional product. Get your copy now for an enhanced user experience!

Share
Download
background image

Appendix A:

 

Test Button

 

AXIS 5470e/570/670e User’s Manual

 

302

 

Factory Default

Settings

Follow the instructions below to reset the AXIS 5470e/570/670e to 
the factory default settings:

1. Remove the external power supply to switch off the AXIS 

5470e/570/670e.

2. Press and hold down the test button, while you plug the external 

power supply back in. Continue to hold down the test button, 
until the network indicator begins to flash at one second intervals. 
This should take at least 5 seconds.

3. Release the test button and wait until the network indicator 

flashes at least five times.

4. Press and hold the test button again until the network indicator 

remains constantly lit.

5. Restart the AXIS 5470e/570/670e by switching it off and on.

The AXIS 5470e/570/670e is now reset to factory default settings.

Note:

All parameters except Node Address (NODE_ADDR) and Internet Address 

(IP_ADDR) are reset. If you want to change these parameters use any standard 

Web browser. Please refer to 

Section 11  Management & Configuration

, 

on page 169

.

Summary of Contents for AXIS 570





























































































































































































































































































































Reviews:

No comments

Related manuals for AXIS 570

Datamax RL4 Quick Start Manual preview
RL4
Brand: Datamax Pages: 2
Samsung CLP-36 Series Manual preview
CLP-36 Series
Brand: Samsung Pages: 9
Samsung Bixolon SRP-500 Command Manual preview
Bixolon SRP-500
Brand: Samsung Pages: 27
Samsung 550N - CLP Color Laser Printer User Manual preview
550N - CLP Color Laser Printer
Brand: Samsung Pages: 288
Samsung 2 COLOR THERMAL PRINTER SRP-275 Quick Reference Manual preview
2 COLOR THERMAL PRINTER SRP-275
Brand: Samsung Pages: 8
Samsung CLP-300 Brochure & Specs preview
CLP-300
Brand: Samsung Pages: 6
Samsung CLP-300 User Manual preview
CLP-300
Brand: Samsung Pages: 91
Oki B411d Guía Del Usuario preview
B411d
Brand: Oki Pages: 154
Oki ML320 Turbo Manual Do Utilizador preview
ML320 Turbo
Brand: Oki Pages: 121
Oki B4100 Guía Del Usuario preview
B4100
Brand: Oki Pages: 96
quadient DS-200iQ User Manual preview
DS-200iQ
Brand: quadient Pages: 130
Xerox 7760DN - Phaser Color Laser Printer User Manual preview
7760DN - Phaser Color Laser Printer
Brand: Xerox Pages: 158
Datamax ST-3210 Programmer'S Manual preview
ST-3210
Brand: Datamax Pages: 26
Seiko LTPD245D Technical Reference preview
LTPD245D
Brand: Seiko Pages: 76
Sun Microsystems Sun Fire V880z Installation And User Manual preview
Sun Fire V880z
Brand: Sun Microsystems Pages: 128
Xerox WorkCentre Pro 90 Compatibility Manual preview
WorkCentre Pro 90
Brand: Xerox Pages: 36
Yeong Yang Cube YY-0430 Technical Instruction preview
Cube YY-0430
Brand: Yeong Yang Pages: 7
Devolinx STE-601C User Manual preview
STE-601C
Brand: Devolinx Pages: 51

Brands by name

Popular brands

Load more brands