manualshive.com logo in svg

Axis AXIS 570, User Manual

Share
Download
Axis AXIS 570 User Manual Download Page 149

 

AXIS 5470e/570/670e

 

User’s Manual

Section 7: Setting Up - Windows

 

149

 

Client-Server Printing:

Client Setup

Follow these steps to use your AXIS 5470e/570/670e for client-server 
printing at a Windows for Workgroups client:

1. In the 

Control Panel

, select 

Printers

.

2. Select a printer driver from the list of Installed Printers, or click 

Add>>

 to install a new driver. Click 

Connect...

3. Select 

Network...

 in the Device Name list, select a local port 

(LPT1 - LPT3) to redirect to your network printer.

4. In the 

Show Shared Printers on list

, select the server from Server 

Setup above.

5. In the Shared Printers list, select the printer you want to use.

6. Click 

OK

, 

OK

 and 

Close

.

7. Exit the Control Panel.

The client setup is completed and you can now print through your 
AXIS 5470e/570/670e.

Note:

Windows Clients using LANtastic

From any Windows client, the AXIS 5470e/570/670e can also be used 
for network printing in LANtastic environments.

You can share the printer drivers you have installed with other AXIS Print System 
users on your network. In AXIS Print System, check the Enable Driver Sharing box 
in My Printers | Settings | Program Options | General. 

Summary of Contents for AXIS 570





























































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands