Axis AXIS 570 User Manual Download

Page: 210 / 316

Section 12: IPP (Internet Printing Protocol)

AXIS 5470e/570/670e User’s Manual

210

6. The

Printer Ports

dialog will appear, showing a list of

Available

Printer Ports

Choose

The HP Internet Printer Connection Port

and click

New

Port.

7. The HP Internet Printer Connection will start. Click

Next

8. In the

IP Address, Host Name or URL

field, type the http://

address of the Axis print server to which the destination printer is
connected. The URL will automatically appear in the

Port Name

field as well:

In this example the printer’s http: address is
http://171.16.5.218:631/LPT1. Click

Next

Summary of Contents for AXIS 570





























































































































































































































































































































Search results

Summary of Contents for AXIS 570

Reviews:

Related manuals for AXIS 570

Brands by name

Popular brands

Axis AXIS 570, User Manual

Search results

Summary of Contents for AXIS 570

Reviews:

Related manuals for AXIS 570

Brands by name

Popular brands