manualshive.com logo in svg

Axis AXIS 570, User Manual

Share
Download
Axis AXIS 570 User Manual Download Page 262

 

Appendix E: IBM Print Formatting

 

AXIS 5470e/570/670e User’s Manual

 

262

 

Paper Orientation

The following table describes the valid paper options:

Note:

ASCII Printer Driver

This parameter should match the printer type you have connected to 
your AXIS 5470e/570/670e. Select the correct printer type from the 
AXIS 5470e/570/670e internal web pages. 

Click 

admin

 | 

IBM Emulators

 | 

Detailed View 

for SCS/IPDS 

Emulator Configuration. Select the desired emulator

 

tab and scroll 

down to the Printer Driver parameter. Click 

OK 

at the bottom of the 

page to save your settings to the print server.

The table below describes the available printer emulation options:

Parameters

Default

Printer Emulation 
Options

Printer Description

BIN1 - BIN 6,

MANUAL,

ENVELOPE,

CONTINUOUS

COR

COR

Computer Output 
Reduction (COR) is 
enabled. 

PORT

Use portrait as default print 
orientation.

LAND

Use landscape as default 
print orientation

COR printouts require a Laser Printer with the following characteristics:

• Landscape orientation.
• Vertically compressed to 70%.
• Horizontally compressed by using a font of higher character density.
• Top and left margins of 0.5 inches each by default.

Summary of Contents for AXIS 570





























































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands