Axis AXIS 570 User Manual Download

Page: 277 / 316

AXIS 5470e/570/670e

User’s Manual

Appendix G: DBCS Support

277

Note

3. Click the

Configuration Wizard for IBM sessions

button.

4. Click the

Add Session

button. This will start the

Configuration

Wizard

which is a step-by-step guide through the required IBM

configuration settings.

Note:

To protect the

admin

pages and the

Configuration Wizard

from unauthorized

use, enter a password (default Pass) in the

Root Password

field under

admin | General Settings

Default fonts will be changed when switching printer emulations.

Summary of Contents for AXIS 570





























































































































































































































































































































Search results

Summary of Contents for AXIS 570

Reviews:

Related manuals for AXIS 570

Brands by name

Popular brands

Axis AXIS 570, User Manual

Search results

Summary of Contents for AXIS 570

Reviews:

Related manuals for AXIS 570

Brands by name

Popular brands