manualshive.com logo in svg

Axis AXIS 570, User Manual

The user manual for the high-performance Axis AXIS 570 is available for free download at manualshive.com. This comprehensive manual provides detailed instructions and information on operating and optimizing the features of this exceptional product. Get your copy now for an enhanced user experience!

Share
Download
background image

Section 4: Setting Up - AS/400

 

AXIS 5470e/570/670e User’s Manual

 

52

 

Configuring the

 AXIS

5470e/570/670e

To perform the instructions presented in this section, you should first 
assign an IP address to your AXIS 5470e/570/670e using one of the 
methods presented in 

Assigning an IP address, 

 on page 32.

Note:

After you have completed the procedures in the AS/400 Host system 
checklist above, follow the instructions below to configure the AXIS 
5470e/570/670e for SNA printing in the AS/400 environment using a 
Web browser:

1. Start a Web browser, e.g. Internet Explorer or Netscape Navigator.

2. Enter the IP address or the host name of the AXIS 

5470e/570/670e in the location field and press the 

Enter

 key on 

your keyboard. The internal Web pages of the AXIS 
5470e/570/670e will appear. 

Note

:

3. Click the 

Configuration Wizard for IBM sessions 

button.

 

If your network does not support the TCP/IP protocol suite, you can still configure 
the AXIS 5470e/570/670e using the AXIS NetPilot installation tool.

To protect the 

admin

 pages and the 

Configuration Wizard

 from unauthorized 

use, enter a password (default Pass) in the 

Root Password

 field under 

admin | General Settings

. 

Summary of Contents for AXIS 570





























































































































































































































































































































Reviews:

No comments

Related manuals for AXIS 570

DataCard CP40 Manual preview
CP40
Brand: DataCard Pages: 2
NCR RealPOS 7199 User Manual preview
RealPOS 7199
Brand: NCR Pages: 224
NCR SelfServ Checkout 7350 Instructions Manual preview
SelfServ Checkout 7350
Brand: NCR Pages: 20
QMS 2060 WX User Manual preview
2060 WX
Brand: QMS Pages: 208
Canon i9100 Series Setup Instructions preview
i9100 Series
Brand: Canon Pages: 2
Oki C931dn Manual Del Usuario preview
C931dn
Brand: Oki Pages: 328
SNBC BTP-R880NP Programming Manual preview
BTP-R880NP
Brand: SNBC Pages: 78
RHINO M10p Manual preview
M10p
Brand: RHINO Pages: 21
VASTEX E20-2024 Assembly And Operation Instructions Manual preview
E20-2024
Brand: VASTEX Pages: 8
Brady BradyJet J4000 User Manual preview
BradyJet J4000
Brand: Brady Pages: 48
Anyload PS805-B User Manual preview
PS805-B
Brand: Anyload Pages: 12
Rice Lake SST4 Technical Manual preview
SST4
Brand: Rice Lake Pages: 86
Citizen CT-S251 User Manual preview
CT-S251
Brand: Citizen Pages: 255
Skynet SoonMark M8 User Manual preview
SoonMark M8
Brand: Skynet Pages: 18
Canon iR7105 Easy Operation Manual preview
iR7105
Brand: Canon Pages: 60
KOMDRUCK IDP-2103 Quick Manual preview
IDP-2103
Brand: KOMDRUCK Pages: 8
Muton VJ-1626UH Installation Manual preview
VJ-1626UH
Brand: Muton Pages: 16
Cisco UCS Invicta C3124SA Manual preview
UCS Invicta C3124SA
Brand: Cisco Pages: 60

Brands by name

Popular brands

Load more brands