Axis AXIS 570 User Manual Download | Manualshive

Page: 232 / 316

background image

Appendix A: SNA Parameter Overview

AXIS 5470e/570/670e User’s Manual

232

Parameter Summary

The following tables summarize SNA host communication parameters
that must be considered when installing the AXIS 5470e/570/670e.

The parameters are presented as:

•

Common Mainframe and AS/400 parameters

•

Mainframe specific parameters

•

AS/400 specific parameters

Common Mainframe

& AS/400 Parameters

Parameter

Name

Default

Description

DEVICE_EMUL

Control Unit
Device
Emulation

3174

This parameter controls the Control Unit
emulation mode. When set to 3174, the Print
Server will appear as a 3174 PU 2.0 node to the
host. This mode may be used for both mainframe
and AS/400 environments.
When set to 5494, the Print Server will appear
as a 5494 PU2.1 node to the host. This is the
recommended mode for the AS/400
environment. The 5494 mode cannot be used in
the mainframe environment.

H1_ADDR

Host MAC
Address

FF FF FF FF FF FF

This is the Host Ethernet/Token Ring MAC
address. It is normally set to the MAC address of
the host.
When the Print Server is connected to the
host through a gateway, this parameter should be
set to the MAC address of the gateway. For a
directly attached AS/400 system, this value is
found in the "Line Description".

AUTODIAL

Automatic Link
Establishment

no

This parameter controls whether the print server
will automatically try to establish the link when
the print server is switched on, or if
communication is lost.
When running 5494 CU mode, this parameter
also controls whether Automatic Configuration
should be performed.

«
...
230
231
232
233
234
...
»

Summary of Contents for AXIS 570





























































































































































































































































































































Reviews:

No comments

Related manuals for AXIS 570

Brand: Oki Pages: 40

Brand: EBS Pages: 34

Brand: TallyGenicom Pages: 3

eserver xSeries 306

Brand: IBM Pages: 46

UniServer R4900 G5

Brand: H3C Pages: 141

Brand: Felix printers Pages: 26

Brand: Buffalo Pages: 80

Brand: 3nStar Pages: 8

NPort W2150Plus Series

Brand: Moxa Technologies Pages: 167

Brand: Olivetti Pages: 8

Brand: 3nStar Pages: 44

Brand: EBS Pages: 20

Brand: Lanier Pages: 4

Brand: Riso Pages: 150

LaCinema PlayHD

Brand: LaCie Pages: 2

EasyCoder PL-Series

Brand: Intermec Pages: 220

Brand: Liene Pages: 64

BullSequana Edge nano

Brand: Atos Pages: 29

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands