Axis AXIS 570 User Manual Download

Page: 184 / 316

Section 11: Management & Configuration

AXIS 5470e/570/670e User’s Manual

184

Printer Information

Follow the instructions below to obtain rich printer information from
printers in the monitoring window:

1. Select the desired printer folder, located in the ‘Monitoring

Printers’ folder.

2. Click the desired printer icon and choose

Printer Information

from the

File

menu.

AXIS NetPilot Printer Information window

You can also view the rich printer information in the Summary
window.

AXIS NetPilot Summary window

AXIS 5470e

Summary of Contents for AXIS 570





























































































































































































































































































































Search results

Summary of Contents for AXIS 570

Reviews:

Related manuals for AXIS 570

Brands by name

Popular brands

Axis AXIS 570, User Manual

Search results

Summary of Contents for AXIS 570

Reviews:

Related manuals for AXIS 570

Brands by name

Popular brands