manualshive.com logo in svg

Axis AXIS 570, User Manual

The user manual for the high-performance Axis AXIS 570 is available for free download at manualshive.com. This comprehensive manual provides detailed instructions and information on operating and optimizing the features of this exceptional product. Get your copy now for an enhanced user experience!

Share
Download
background image

Section 10: Setting Up - UNIX

 

AXIS 5470e/570/670e User’s Manual

 

164

 

Integration into the

Host Printer Spooler

To integrate the AXIS 5470e/570/670e into the host printer spooler, 
you can use the auto installation script axinstall, resident in the AXIS 
5470e/570/670e. Follow the instructions below to install axinstall 
onto your host using FTP:

1. Login to the AXIS 5470e/570/670e using the command:

ftp <host name>

 or 

ftp <IP address>

2. Enter 

root

 as the user id and 

pass

 as the password.

3. Download the script using the command:

get axinstall

 

Log out using the command 

quit,

 

bye

 or 

exit

 depending on your 

FTP version.

Typical FTP session for collecting the axinstall script

> ftp npserver

connected to npserver.

220 AXIS 5470e/570/670e FTP Print Server v6.00 Jun 17

1999 ready.

Name (npsserver:thomas): root

331 User name ok, need password

Password: pass

(not visible)

230 User logged in

ftp> get axinstall

200 PORT command successful.

150 Opening data connection for axinstall

(192,36,253,4,13,223), (mode ascii).

226 Transfer complete.

local: axinstall remote: axinstall

61187 bytes received in 14 seconds (4.2 kbytes/s)

ftp> bye

221 Goodbye.

>

Summary of Contents for AXIS 570





























































































































































































































































































































Reviews:

No comments

Related manuals for AXIS 570

Radio Shack DMP-200 Operation Manual preview
DMP-200
Brand: Radio Shack Pages: 62
NAIM HDX-SSD - Quick Start Manual preview
HDX-SSD -
Brand: NAIM Pages: 16
Xerox PHASER 6250 Reference Manual preview
PHASER 6250
Brand: Xerox Pages: 9
Xerox PHASER 6250 Management Manual preview
PHASER 6250
Brand: Xerox Pages: 2
Xerox PHASER 6250 Setting Instructions Manual preview
PHASER 6250
Brand: Xerox Pages: 8
Xerox Phaser 6200 Function Manual preview
Phaser 6200
Brand: Xerox Pages: 4
Xerox Phaser 4622 User Manual preview
Phaser 4622
Brand: Xerox Pages: 150
Xerox Phaser 4600 Supplementary Manual preview
Phaser 4600
Brand: Xerox Pages: 4
Xerox Phaser 4 400 Driver Installation Instruction preview
Phaser 4 400
Brand: Xerox Pages: 6
Xerox VersaLink C400 Installation Manual preview
VersaLink C400
Brand: Xerox Pages: 2
Xerox DocuPrint N2125 System Administrator Manual preview
DocuPrint N2125
Brand: Xerox Pages: 246
Xerox DocuPrint N2025 Service Manual preview
DocuPrint N2025
Brand: Xerox Pages: 378
Xerox DocuPrint N2025 User Manual preview
DocuPrint N2025
Brand: Xerox Pages: 176
Xerox DocuPrint C3290 FS User Manual preview
DocuPrint C3290 FS
Brand: Xerox Pages: 240
Xerox Phaser 6120N Guia De Utilização Rápida preview
Phaser 6120N
Brand: Xerox Pages: 5
Xerox Phaser 6100 Quick Reference Manual preview
Phaser 6100
Brand: Xerox Pages: 7
Xerox Phaser 6100 Setup Manual preview
Phaser 6100
Brand: Xerox Pages: 2
Xerox Phaser 8200 Networking Setup Manual preview
Phaser 8200
Brand: Xerox Pages: 47

Brands by name

Popular brands

Load more brands