Axis AXIS 570 User Manual Download

Page: 63 / 316

AXIS 5470e/570/670e

User’s Manual

Section 4: Setting Up - AS/400

Configuring the AXIS

5470e/670e

Follow the instructions below to configure your AXIS 5470e/670e
using a standard Web browser:

1. Start a Web browser, e.g. Internet Explorer or Netscape Navigator.

2. Enter the IP address or the host name of the AXIS 5470e/670e in

the location field and press the

Enter

key on your keyboard. The

internal Web pages of the AXIS 5470e/670e will appear.

Note

3. Click the

Configuration Wizard for IBM sessions

button.

4. Click the

Add Session

button. This takes you to the

Configuration Wizard

which is a step-by-step guide through the

required configuration settings.

To protect the

admin

pages and the

Configuration Wizard

from unauthorized

use, enter a password (default Pass) in the

Root Password

field under

admin | General Settings

Summary of Contents for AXIS 570





























































































































































































































































































































Search results

Summary of Contents for AXIS 570

Reviews:

Related manuals for AXIS 570

Brands by name

Popular brands

Axis AXIS 570, User Manual

Search results

Summary of Contents for AXIS 570

Reviews:

Related manuals for AXIS 570

Brands by name

Popular brands