Axis AXIS 570 User Manual Download | Manualshive

Page: 138 / 316

background image

Section 7: Setting Up - Windows

AXIS 5470e/570/670e User’s Manual

138

Installing a printer

Follow the instructions below to install a printer for LPD printing:

1. Open the

Control Panel

and open the ‘Printers’ folder.

2. Click

Add Printer

, select

My Computer

and then go to

Next

.

3. Select

Add Port

. In Printer Ports, choose

LPR Port

and then click

New Port

.

4. In Add LPR compatible printer, enter the host name or IP address

of the AXIS 5470e/570/670e as the print server to provide LPD.

5. Enter 'pr1', 'pr2', ... 'pr8' as the name of printer or print queue on

that server.

6. Choose a suitable printer driver for your printer and go to

Next

.

7. Enter a printer name and go to

Next

.

8. Enter a share name.

9. Click

Next

and then

Finish

.

AXIS Print Monitor Overview

AXIS Print Monitor is the recommended tool to use for network
printing in Windows NT 3.5x environments. It allows AXIS Network
Print Servers to be connected in the same simple fashion as a local
printer port and once installed, is automatically initialized upon
system startup. AXIS Print Monitor has been developed for peer-to-
peer printing, allowing your print jobs to be sent directly to the print
server.

Printing Environments

AXIS Print Monitor supports printing over NetBIOS/NetBEUI and
TCP/IP (LPR). To enable printing in these environments, please
ensure that the desired printing protocols are running on your client.

«
...
136
137
138
139
140
...
»

Summary of Contents for AXIS 570





























































































































































































































































































































Reviews:

No comments

Related manuals for AXIS 570

Brand: Canon Pages: 358

Brand: IBM Pages: 64

BladeCenter HS23

Brand: IBM Pages: 28

Brand: QMS Pages: 144

Pixma TS7700i Series

Brand: Canon Pages: 554

Brand: ExtraHop Pages: 5

Brand: Xerox Pages: 13

TELEIOS GRANDE G5

Brand: d.gen Pages: 14

eserver xSeries 306

Brand: IBM Pages: 46

Brand: ACE COMPUTERS Pages: 32

Brand: Rimage Pages: 217

8860MFPD - Multifunction Inkjet Printer

Brand: Xerox Pages: 16

1235/DX - Phaser Color Laser Printer

Brand: Xerox Pages: 144

Brand: 3onedata Pages: 3

Brand: WOOSIM Pages: 19

Brand: Kontron Embedded Computers Pages: 46

Brand: Brother Pages: 10

Brand: Brother Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands