Axis AXIS 570 User Manual Download | Manualshive

Page: 245 / 316

background image

AXIS 5470e/570/670e

User’s Manual Appendix C: Extended IBM Printer Emulation

245

Appendix C Extended IBM Printer

Emulation

When printing from an IBM host, the AXIS 5470e/570/670e allows
you to make use of the following printer functions not found in
standard IBM printers:

•

Configuration Mode

•

Hex Transparency

•

User Defined Strings

•

String Substitutions

•

Bar Codes

•

Font Selection.

This appendix provides a brief overview of some of these functions.
For more information, please refer to the AXIS Network Print Server
Technical Reference supplied on the AXIS Product CD.

Configuration Mode

The Configuration Mode provides a way to configure your AXIS
5470e/570/670e from your IBM system. For more information see

SNA Parameter Overview

(page 231).

User Defined Strings

The User Definable Strings are a set of 256 programmable sequences.
The UDS are useful for storing long sequences, such as printer
function sequences, within the AXIS 5470e/570/670e. Each sequence
can be activated by inserting a short control command in your
documents.

String Substitutions

The String Substitution function searches the output data stream for
specified sequences of AIC characters (Match Strings), and substitutes
them with other sequences (Substitute Strings). Up to 128 pairs of

«
...
243
244
245
246
247
...
»

Summary of Contents for AXIS 570





























































































































































































































































































































Reviews:

No comments

Related manuals for AXIS 570

Brand: IBM Pages: 214

Univerge SV9300

Brand: NEC Pages: 47

Univerge SV9100

Brand: NEC Pages: 766

Magicolor 2 plus

Brand: QMS Pages: 90

Magicolor 2 Desklaser

Brand: QMS Pages: 4

Brand: QMS Pages: 8

Brand: QMS Pages: 94

Brand: QMS Pages: 6

Brand: Unimark Pages: 36

Brand: BCS Pages: 151

ioLogik W5300 Series

Brand: Moxa Technologies Pages: 177

Brand: Oki Pages: 2

eServer 380 xSeries

Brand: IBM Pages: 112

Virtual Services Platform 7000 Series

Brand: Avaya Pages: 103

Brand: Vxl Pages: 2

N2400 - TaskSmart - 1 GB RAM

Brand: Compaq Pages: 372

Brand: SAGEMCOM Pages: 146

DocuPrint C2535 A

Brand: Xerox Pages: 120

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands