Axis AXIS 570 User Manual Download Page 69

Page: 69 / 316

AXIS 5470e/570/670e

User’s Manual

Section 5: Setting Up - IBM Mainframe

3. Make sure that the corresponding

VTAM Logon-mode

entries

are available and that the appropriate

session types (

LU1

LU3

) are used.

Vary ACTive

the

VTAM Major Node

definition for the

AXIS 5470e/570/670e.

Sample Sessions

The examples below are based on samples given in

VTAM

Customization

(IBM part no: SC23-0112), with some changes

to optimize use for AXIS 5470e/570/670e.

VTAM for MVS is assumed, although the configuration for VM and
VSE is similar.

Logon-mode Entry

Creating a VTAM Logon-mode entry for your AXIS
5470e/570/670e.

Example: (Logon-mode entry for LU type 1 printing)

* For application output of LU-1 SNA Character Stream (SCS)

TITLE ‘SCS5470e’

SCS5470e

MODEENT

LOGMODE=SCS5470e,

FMPROF=X’03’,

TSPROF=X’03’,

PRIPROT=X’B1’,

SECPROT=X’B0’,

COMPROT=X’3080’,

RUSIZES=X’8585’,

PSERVIC=X’014000010000000001000000’,

PSNDPAC=X’03’,

SRCVPAC=X’03’

Summary of Contents for AXIS 570





























































































































































































































































































































Search results

Summary of Contents for AXIS 570

Reviews:

Brands by name

Popular brands

Axis AXIS 570, User Manual

Search results

Summary of Contents for AXIS 570

Reviews:

Brands by name

Popular brands