Axis AXIS 570 User Manual Download | Manualshive

Page: 101 / 316

background image

AXIS 5470e/570/670e

User’s Manual

Section 5: Setting Up - IBM Mainframe

101

DEVICE Statement:

A DEVICE statement is required for each printer. The DEVICE
parameters create JES3 default values that are used unless other values
are specified in the JCL application program. The DEVICE
statement can contain the following parameters:

Device Statement

Explanation

CARRIAGE

Specifies the JES default page definition.

The value

YES

specifies that the page definition can be changed

during startup procedures.

The value

NO

specifies that the page definition cannot be changed

during startup procedures.

The value

aaaa

specifies that the un-prefixed name, 1 to 4 characters

long, of the page definition is to be used as default. The name specified
here, or the JES3 system default, is the PSF default page definition.

CHARS

Specifies a default JES3 font.

CKPNTPG

Specifies the number of pages between data-set checkpoints. If
checkpoint intervals are too frequent, printer performance is significantly
reduced. If intervals are too infrequent, and a PSF error occurs, the job
has to be reprocessed from the last checkpoint. In this case, printer
performance is significantly reduced if PSF errors continue to occur. The
recommended starting value is 100.

DTYPE

Identifies the printer device type. For the AXIS 5470e/570/670e you
should specify the parameter value

PRTAFP1

. This parameter is

required.

FSSNAME

Specifies a unique FSS for this printer DEVICE statement. The value
must match the value coded for the FSSNAME parameter in the
corresponding FSSDEF statement.

HEADER

Specifies if job and data set header pages are printed. If DPF is
installed, you may need to specify HEADER=YES.

JNAME

Specifies the name of the printer FSA. Each printer FSA should have a
unique JNAME. This unique JNAME is 8 characters or fewer and must
correspond to its label on the

CNTL

,

ENDCNTL

, and

PRINTDEV

statements for the PSF startup procedure specified in the

PNAME

parameter. This parameter is required.

«
...
99
100
101
102
103
...
»

Summary of Contents for AXIS 570





























































































































































































































































































































Reviews:

No comments

Related manuals for AXIS 570

Brand: Olympus Pages: 71

imagePRESS Server G200

Brand: Canon Pages: 82

Brand: Canon Pages: 88

Brand: IBM Pages: 16

BladeCenter HS23

Brand: IBM Pages: 36

Brand: Oki Pages: 40

Brand: Dascom Pages: 138

Brand: Dascom Pages: 166

Brand: Xerox Pages: 3

Versant 3100 Press

Brand: Xerox Pages: 45

Brand: Omega Pages: 49

Brand: Iwatsu Pages: 338

Transport TN27 B4987

Brand: TYAN Pages: 135

Brand: Riso Pages: 150

BladeCenter PS703

Brand: IBM Pages: 198

Brand: DataCard Pages: 204

PRIMERGY CX120 S1

Brand: Fujitsu Pages: 82

PRIMERGY BX922 S2

Brand: Fujitsu Pages: 106

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands