Axis AXIS 570 User Manual Download | Manualshive

Page: 223 / 316

background image

AXIS 5470e/570/670e

User’s Manual

Section 13: Using Logical Printers

223

Debugging using the

Hex Dump Mode

When hex dump mode is activated, the print data is printed as
hexadecimal byte values rather than characters; printer control
commands are also printed as hex values. This allows you to inspect
the control and print characters that are being sent to the printer,
which is a useful debugging facility for the more difficult printing
problems.

Example:

Follow the instructions below to activate the hex dump mode for PR1:

1. Click

admin

and the

Logical Printer Settings

button.

2. Select the

PR1

tab.

3. Set the

Hex Dump Mode Enabled

radio button to

YES

.

4. Click

OK

.

Note:

PostScript Settings

When a logical printer is set for PostScript conversion, you must
specify the following:

•

page size (default A4)

•

page orientation (default Portrait)

•

page format (see table below)

•

font (default Courier)

Note:

The page length for hex dump printouts is determined by the lines per page value
of the PostScript page format parameter.

The PostScript font can be any font that is installed on the printer.

Page Format Parameter

Default Value

Description

Lines per page

66

Characters per line

0

0=disable line wrap

Characters per inch

100

100=10 characters per inch

Lines per inch

60

60 = 6 lines per inch

Left margin

30

30 = 3.0 mm

Top margin

50

50 = 5.0 mm

«
...
221
222
223
224
225
...
»

Summary of Contents for AXIS 570





























































































































































































































































































































Reviews:

No comments

Related manuals for AXIS 570

Brand: Saxxot Pages: 13

Jetprinter Disney Edition Z615 Series

Brand: Lexmark Pages: 2

Brand: Dascom Pages: 12

Brand: Dascom Pages: 19

Brand: Dascom Pages: 5

Brand: Panduit Pages: 74

Brand: Tally Pages: 2

Brand: Tally Dascom Pages: 57

Brand: Fenix Pages: 65

Brand: DataCard Pages: 7

6219 - IntelliStation M - Pro

Brand: IBM Pages: 317

e Server iSeries 825

Brand: IBM Pages: 52

5550B - Phaser B/W Laser Printer

Brand: Xerox Pages: 117

Brand: Omega Pages: 16

LaserPro StellarMark IFII Series

Brand: GCC Technologies Pages: 111

Brand: Advantech Pages: 96

Brand: MAXPhotonics Pages: 24

FusionServer 1288H V5

Brand: xFusion Digital Technologies Pages: 96

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands