Axis AXIS 570 User Manual Download | Manualshive

Page: 79 / 316

background image

AXIS 5470e/570/670e

User’s Manual

Section 5: Setting Up - IBM Mainframe

79

Configuring the

TN3270E server

The TN3270E server may be implemented as a software package
running on the mainframe itself, a router or other server hardware.

Configuration examples for two popular TN3270E-capable servers are
described below, namely:

•

Microsoft SNA Server

•

Novell NetWare for SAA.

Typical AXIS 5470e/570/670e TCP/IP TN3270E Network Configuration

Note:

Microsoft SNA Server

Communication is established in two separate stages, SNA Server-to-
Host connection and SNA Server to AXIS 5470e/570/670e
connection, as described below:

SNA Server-to-Host Connection

Follow the steps below to set-up a SNA Server-to-Host connection for
the AXIS 5470e/570/670e:

1. Start Microsoft SNA Server Manager and click the Servers folder.

The Main SNA Server Manager Window is featured in the
illustration below.

2. Insert a new Connection to the host under Connections. Refer to

the online help for assistance on how to configure the connection.

•

Configuration procedures can differ from other TN3270E servers.

•

For additional information about configuring other TN3270E servers, refer to
the Technical Notes section on the AXIS Web pages.

«
...
77
78
79
80
81
...
»

Summary of Contents for AXIS 570





























































































































































































































































































































Reviews:

No comments

Related manuals for AXIS 570

Brand: QMS Pages: 160

Brand: QMS Pages: 110

Brand: QMS Pages: 158

Brand: CAB Pages: 144

Brand: A10 Networks Pages: 17

Brand: Acano Pages: 17

Brand: Seiko Pages: 76

eserver xSeries 306

Brand: IBM Pages: 46

Brand: TYAN Pages: 64

Brand: Oki Pages: 255

Brand: AstroJet Pages: 32

Brand: Novexx Solutions Pages: 6

System x3650 M5

Brand: IBM Pages: 1010

MediaGrid ContentServer 3000

Brand: Omneon Pages: 2

Brand: TEC Pages: 92

Brand: Kyocera Pages: 44

Brand: Samsung Pages: 17

Brand: DataMetrics Pages: 35

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands