manualshive.com logo in svg

Axis AXIS 570, User Manual

Share
Download
Axis AXIS 570 User Manual Download Page 273

 

AXIS 5470e/570/670e User’s Manual

Appendix F: IPDS Overview

 

273

 

The AXIS 5470e/570/670e supports extended font mapping at 
PostScript level, making it possible to redefine any of the FGIDs. 

Immediate Font Substitutions

Certain FGIDs will be immediately substituted by the AXIS 
5470e/570/670e. The substitution table depends on the selected IBM 
printer emulation.

Unsupported Fonts

A selection of an unsupported FGID value will result in a substitution 
to a default font. The AXIS 5470e/570/670e uses the same default 
fonts as the emulated IBM printers. 

0104 - 0111

260 - 273

8 CPI

0112 - 0117

274 - 279

17 CPI

0118 - 011B

280 - 283

20 CPI

011C - 0120

284 - 288

25 CPI

0121 - 012B

289 - 299

27 CPI

012C - 01FF

300 - 511

10 CPI

FGID (hex)

FGID (dec)

TYPE

0200 - 0EFF

512 - 3839

Typographic

0F00 - 0FFF

3840 - 4095

User Defined Fonts

1000 - FFFE

4096 - 65534

Typographic

Summary of Contents for AXIS 570





























































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands