manualshive.com logo in svg

Axis AXIS 570, User Manual

The user manual for the high-performance Axis AXIS 570 is available for free download at manualshive.com. This comprehensive manual provides detailed instructions and information on operating and optimizing the features of this exceptional product. Get your copy now for an enhanced user experience!

Share
Download
background image

Section 3: Basic Installation

 

AXIS 5470e/570/670e User’s Manual

 

42

 

Example - AXIS 670e Token Ring Print Servers:

Notes:

2. If necessary, update your host table and alias name databases, as 

required by your system.

3. If it is not already running, start the BOOTP daemon. This is 

typically performed using the 

bootpd

 command. 

4. Restart the AXIS 5470e/570/670e to download the IP address, 

default router address and subnet mask. 

The AXIS 5470e/570/670e can automatically download a customized 
config file from a TFTP server. Just add the name of the config file 
and the TFTP server’s IP address to your boot table. The config file is 
downloaded immediately after the AXIS 5470e/570/670e receives its 
IP address.

npsname:ht=tr:vm=rfc1048:\

:ha=000231480061:ip=192.168.3.191:\

:sm=255.255.255.0:gw=192.168.1.1

•

Enter the

ht

 and 

vm

 fields exactly as shown in the example. 

•

The 

ha

 field is the Ethernet address/node address and the

ip

field is the IP 

address of your AXIS 5470e/570/670e.

•

The 

gw

 and 

sm

 fields correspond to the default router address and subnet 

mask.

Summary of Contents for AXIS 570





























































































































































































































































































































Reviews:

No comments

Related manuals for AXIS 570

IBM BladeCenter HS23 Service Manual preview
BladeCenter HS23
Brand: IBM Pages: 36
Pandigital M1 Setup Instruction preview
M1
Brand: Pandigital Pages: 2
UltraTape UltraLabel PRO User Manual preview
UltraLabel PRO
Brand: UltraTape Pages: 52
Xerox Phaser 5335 Installation Manual preview
Phaser 5335
Brand: Xerox Pages: 2
Datamax MP-Compact4 Programmer'S Reference Manual preview
MP-Compact4
Brand: Datamax Pages: 95
Datamax Mark II E-4205e Operator'S Manual preview
Mark II E-4205e
Brand: Datamax Pages: 72
Magicard Tango 2e Brochure preview
Tango 2e
Brand: Magicard Pages: 2
Magicard Tango 2e Quick Start Manual preview
Tango 2e
Brand: Magicard Pages: 2
Quest Payment Systems Donation Point Even Quick Start Manual preview
Donation Point Even
Brand: Quest Payment Systems Pages: 2
Printek DP-530si Operator'S Manual preview
DP-530si
Brand: Printek Pages: 34
Oce Arizona 180 GL User Manual preview
Arizona 180 GL
Brand: Oce Pages: 268
MAC TOOLS P 9300 Instruction Manual preview
P 9300
Brand: MAC TOOLS Pages: 2
Oki MPS730b Manual De L'Utilisateur preview
MPS730b
Brand: Oki Pages: 143
SPRT SP-RMT12 User Manual preview
SP-RMT12
Brand: SPRT Pages: 14
B&B Electronics VESR4x4 Quick Start Manual preview
VESR4x4
Brand: B&B Electronics Pages: 2
Canon imageRUNNER ADVANCE DX C5870i Faq Manual preview
imageRUNNER ADVANCE DX C5870i
Brand: Canon Pages: 100
Canon imageRUNNER ADVANCE C356iF Faq Manual preview
imageRUNNER ADVANCE C356iF
Brand: Canon Pages: 96
Canon imageRUNNER ADVANCE C350 series Service Manual preview
imageRUNNER ADVANCE C350 series
Brand: Canon Pages: 1173

Brands by name

Popular brands

Load more brands