Axis AXIS 570 User Manual Download | Manualshive

Page: 196 / 316

background image

Section 11: Management & Configuration

AXIS 5470e/570/670e User’s Manual

196

Exceptions

Even though the AXIS 5470e/570/670e is fully compatible with the
HP JetAdmin tool, the AXIS 5470e/570/670e behaves differently
than an HP print server in certain situations. The exceptions from the
traditional HP JetAdmin functionality are presented below.

The print server

concept

HP JetAdmin considers each printer port of the HP print server as an
independent print server. One physical HP print server will act as one
or three print servers depending on the number of supported printer
ports. HP JetAdmin always considers the AXIS 5470e/570/670e as
one print server, independent of the number of supported ports. The
effects of this different behavior are:

•

You can change a printer port’s properties from any of the AXIS
5470e/570/670e printer ports’ property pages. This can not be
done with an HP print server.

•

If you are performing a reset on one of the AXIS 5470e/570/670e
printer ports, all three ports will be reset.

•

From each port you can view all print queues connected to the
print server and not only the queues connected to the specific
printer port. To be able to distinguish between the queues, they
must be named <queue_name>!<logical_printer_number>.

•

The AXIS 5470e/570/670e printer ports have the same name.
They are only distinguished by suffixes. If you change the name
on one of the AXIS 5470e/570/670e printer ports, all three port
names will be changed. Note that the port names displayed in HP
JetAdmin will not change until one of the refresh commands in
the Device Refresh menu has been performed.

«
...
194
195
196
197
198
...
»

Summary of Contents for AXIS 570





























































































































































































































































































































Reviews:

No comments

Related manuals for AXIS 570

Brand: YOUPAI Pages: 15

Brand: TallyGenicom Pages: 15

eServer 200 xSeries

Brand: IBM Pages: 128

eServer 232 xSeries

Brand: IBM Pages: 174

Brand: Xerox Pages: 44

Brand: Oki Pages: 76

Brand: OKIDATA Pages: 13

Brand: Galleon Pages: 35

BladeCenter PN41

Brand: IBM Pages: 88

Vlinx Serial Servers ESP901E

Brand: B&B Electronics Pages: 92

Brand: Oki Pages: 80

AMD Opteron LS20 Type 8850

Brand: IBM Pages: 68

Brand: Radio Shack Pages: 42

3CRWPS10075-US - OfficeConnect Wireless 54Mbps 11g Print...

Brand: 3Com Pages: 94

Brand: SANEI ELECTRIC Pages: 60

Brand: Oki Pages: 20

IMAGE M4100 Series

Brand: G&G Pages: 147

Brand: Pathos Acoustics Pages: 26

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands