Axis AXIS 570 User Manual Download

Page: 177 / 316

AXIS 5470e/570/670e

User’s Manual

Section 11: Management & Configuration

177

Managing the

print servers

Follow the instructions below to access the AXIS 5470e/570/670e
using AXIS ThinWizard:

1. Click the

Manage Network

button in the main menu.

2. Select the network group, including the AXIS 5470e/570/670e,

from the drop-down list. All AXIS servers included in the network
group appear in the window.

3. Click the link of the AXIS 5470e/570/670e to access its internal

Web page.

You are now free to manage and configure the AXIS 5470e/570/670e
as described in

Using a Web browser

on page 170.

Upgrading

Axis Servers

Refer to

Upgrading using AXIS ThinWizard

on page 228, for more

information about upgrading Axis Servers using AXIS ThinWizard.

Additional

Information

If you need more information, please refer to the AXIS ThinWizard
on-line help.

Summary of Contents for AXIS 570





























































































































































































































































































































Search results

Summary of Contents for AXIS 570

Reviews:

Related manuals for AXIS 570

Brands by name

Popular brands

Axis AXIS 570, User Manual

Search results

Summary of Contents for AXIS 570

Reviews:

Related manuals for AXIS 570

Brands by name

Popular brands