manualshive.com logo in svg

Axis AXIS 570, User Manual

Share
Download
Axis AXIS 570 User Manual Download Page 24

Section 2: Product Overview

 

AXIS 5470e/570/670e User’s Manual

 

24

 

Test Button

The test button is used for:

•

Printing a test page to check the connection to the printer.

•

Printing the parameter list showing all the AXIS 670e settings. 

•

Resetting the AXIS 670e parameters to the factory default 
settings.

Refer to 

Appendix A - Test Button

, on page 301 for more 

information about the test button.

Ring Speed Switch

This switch is set to match your network speed.

Network Indicator

The network indicator flashes to indicate network activity.

Power Indicator

The power indicator is lit while power is applied. If it is not lit, or it 
flashes, there is a problem with the AXIS 670e or its power supply.

Summary of Contents for AXIS 570





























































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands