Axis AXIS 570 User Manual Download | Manualshive

Page: 54 / 316

background image

Section 4: Setting Up - AS/400

AXIS 5470e/570/670e User’s Manual

54

TN5250E printing

TN5250E is the recommended protocol to use when printing SCS
data streams over TCP/IP. This print method offers superior control,
management and throughput for the AXIS 5470e/570/670e.

Before you begin

Make sure that the AS/400 host is running OS/400 V3R2 or higher
with TCP/IP support installed and configured.

Make sure that the latest PTFs are installed. Information about which
PTFs to use can be obtained from:

The AS/400 Host

System Checklist

Note:

1. Type

WRKCTLD *VWS

on the AS/400 command line and press

Enter

to determine the number of auto-configured virtual devices

on your AS/400 system. Press

F3.

2. Type

DSPSYSVAL QAUTOVRT

and press

Enter

.

Make sure

that the value of the

QAUTOVRT

parameter is greater than the

number of auto-configured virtual devices. Press

F3

.

3. Type

DSPSYSVAL QCHRID

and press

Enter.

Note the system

language (code page) for future reference. Press

F3

.

4. Type

WRKTCPSTS OPTION *IFC

and press

Enter

to

determine the IP address of the AS/400 server. Press

F3

.

http://as400service.rochester.ibm.com/

There is an AS/400 Parameter checklist in the AXIS 5470e/570/670e User’s Guide
where you can enter the values described in this section for future reference.

«
...
52
53
54
55
56
...
»

Summary of Contents for AXIS 570





























































































































































































































































































































Reviews:

No comments

Related manuals for AXIS 570

Univerge SV9100

Brand: NEC Pages: 78

UNIVERGE SL2100

Brand: NEC Pages: 34

Brand: NEC Pages: 2

Brand: NEC Pages: 975

eserver pSeries 690

Brand: IBM Pages: 142

eServer 370 xSeries

Brand: IBM Pages: 218

BladeCenter PS703

Brand: IBM Pages: 298

BladeCenter T Type 8720

Brand: IBM Pages: 180

Brand: VASTEX Pages: 2

mC-Print3 MCP31LB

Brand: Star Pages: 12

Brand: Vxl Pages: 2

Brand: Maxim Pages: 69

Brand: Kontron Pages: 110

Brand: Galleon Pages: 47

Brand: Ricoh Pages: 17

Brand: IBM Pages: 51

Brand: Printekmobile Pages: 2

Brand: B&B Electronics Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands