manualshive.com logo in svg

Axis AXIS 570, User Manual

The user manual for the high-performance Axis AXIS 570 is available for free download at manualshive.com. This comprehensive manual provides detailed instructions and information on operating and optimizing the features of this exceptional product. Get your copy now for an enhanced user experience!

Share
Download
background image

 

AXIS 5470e/570/670e

 

User’s Manual Appendix C: Extended IBM Printer Emulation

 

247

 

Resulting printout:

Bar Codes

The bar code function provides easy access to a range of standard bar 
code types resident in the AXIS 5470e/570/670e. Bar codes can only 
be printed on PCL printers.

Before the bar codes can be printed, a bar code format has to be 
defined. This format sets the type and size of the bar code to be 
printed. Up to 16 formats can be predefined. The definitions are made 
by setting up the BAR parameter. 

The BAR parameter takes several arguments, separated by commas, as 
shown below:

•

number

 is the bar code definition number in the range 0–15. This 

number is used to refer to the definition when printing the bar 
code.

•

type

 is the predefined bar code type. Valid values are:

The word underline is underlined

You can also use quoted text.

BAR <number>=<type>,<width>,<height>,<text mode>,

<check mode>;

Value

Description

Value

Description

CODE39

Code 39

CODE128

Code 128

UPCA

UPC version A

INT2OF5

2 of 5 Interleaved

EAN8

EAN-8

CODABAR

Codabar matrix

EAN13

EAN-13

Summary of Contents for AXIS 570





























































































































































































































































































































Reviews:

No comments

Related manuals for AXIS 570

NEC HX4500 Configuration Manual preview
HX4500
Brand: NEC Pages: 74
NEC Express5800/T120e Quick Start Manual preview
Express5800/T120e
Brand: NEC Pages: 6
NEC Express5800/T120e Getting Started preview
Express5800/T120e
Brand: NEC Pages: 2
NEC Express5800/T110i Getting Started preview
Express5800/T110i
Brand: NEC Pages: 2
NEC EXPRESS5800/R320d-E4 Configuration Manual preview
EXPRESS5800/R320d-E4
Brand: NEC Pages: 19
NEC Express5800/R320d-M4 Series User Manual preview
Express5800/R320d-M4 Series
Brand: NEC Pages: 98
NEC Express5800/R120h-2M Getting Started preview
Express5800/R120h-2M
Brand: NEC Pages: 2
NEC Express5800/R120f-1E Use Precautions preview
Express5800/R120f-1E
Brand: NEC Pages: 12
NEC Express5800/R120d-1E Hardware Specification preview
Express5800/R120d-1E
Brand: NEC Pages: 2
NEC Express5800/R110i-1 Getting Started preview
Express5800/R110i-1
Brand: NEC Pages: 2
NEC Express5800/R110h-1 System Configuration Manual preview
Express5800/R110h-1
Brand: NEC Pages: 40
NEC Express5800/A2040d Configuration Manual preview
Express5800/A2040d
Brand: NEC Pages: 83
NEC Express5800/320Lc Datasheet preview
Express5800/320Lc
Brand: NEC Pages: 4
NEC Express5800/120Rj-2 Datasheet preview
Express5800/120Rj-2
Brand: NEC Pages: 2
NEC NEAX2000 IVS2 Manual preview
NEAX2000 IVS2
Brand: NEC Pages: 106
NEC Express5800/T120d User Manual preview
Express5800/T120d
Brand: NEC Pages: 153
NEC Express5800/T110g-S User Manual preview
Express5800/T110g-S
Brand: NEC Pages: 128
NEC Express5800/R120g-1E Maintenance Manual preview
Express5800/R120g-1E
Brand: NEC Pages: 224

Brands by name

Popular brands

Load more brands