manualshive.com logo in svg

Argus 152, Manual

The Kenmore 152 is a versatile and reliable appliance that simplifies your daily chores. To gain full control and maximize its potential, make sure to download the comprehensive Owner's Manual from manualshive.com for free. This handy manual is your go-to resource, offering detailed instructions and tips for optimal product usage.

Share
Download
background image

26 ARGUS settings

ARGUS 152

 

363

26.3 Restoring the factory settings

ARGUS resets all settings to the factory defaults.

The speed-dial memory, PPP user name and password, IP addresses, profile-
names, user-specific services, keypad information and all test results stored in 
ARGUS are erased.

All parameters are reset to the factory 
defaults.

ARGUS jumps directly to 
the security prompt.

Enter the security password to 
delete all settings.

You can obtain this from Technical 
Support or directly from intec (see 
page 10).

Restores the saved test 
settings.

If no settings have been backed 
up, this function has the same 
effect as "Restore factory 
defaults", see page 362.

Settings

Backup/restore

The following steps are performed 
as for "Backup settings", see 
page 361.

and

and

Summary of Contents for 152

























































































































































































































































































































































































































Reviews:

No comments

Related manuals for 152

D-Link ShareCenter DNS-320L Datasheet preview
ShareCenter DNS-320L
Brand: D-Link Pages: 4
IBM 51 Troubleshooting Manual preview
51
Brand: IBM Pages: 248
?omtime CT-Router LAN User Manual preview
CT-Router LAN
Brand: ?omtime Pages: 62
NA DigiNet 416 User Manual preview
DigiNet 416
Brand: NA Pages: 22
NETGEAR RP614 v2 Installation Manual preview
RP614 v2
Brand: NETGEAR Pages: 2
ZyXEL Communications PK5000Z How To Configure preview
PK5000Z
Brand: ZyXEL Communications Pages: 3
Ubiquiti PBE-M5-400-ISO Quick Start Manual preview
PBE-M5-400-ISO
Brand: Ubiquiti Pages: 28
ZyXEL Communications SHD1110 Quick Start Manual preview
SHD1110
Brand: ZyXEL Communications Pages: 12
Modecom MC-421 Quick Installation Manual preview
MC-421
Brand: Modecom Pages: 16
Deliberant APC Mach 5 V3 Quick Installation Manual preview
APC Mach 5 V3
Brand: Deliberant Pages: 16
Proxim Lynx.GX 16T Installation And Management Manual preview
Lynx.GX 16T
Brand: Proxim Pages: 45
mikroElektronika mikroETH 100 Manual preview
mikroETH 100
Brand: mikroElektronika Pages: 6
Cisco ASR 9001 Hardware Installation Manual preview
ASR 9001
Brand: Cisco Pages: 160
Gamma Solution TITANUS MX Series Quick Start Manual preview
TITANUS MX Series
Brand: Gamma Solution Pages: 7
Siemens SL2-141-I Quick Start Manual preview
SL2-141-I
Brand: Siemens Pages: 24
Siemens SLI-5310 User Manual preview
SLI-5310
Brand: Siemens Pages: 128
Siemens SL2-141 User Manual preview
SL2-141
Brand: Siemens Pages: 144
Edimax AR-7084A User Manual preview
AR-7084A
Brand: Edimax Pages: 86

Brands by name

Popular brands

Load more brands