Argus 152 Manual Download Page 67

Page: 67 / 408

7 Operation on xDSL accesses

ARGUS 152

The VDSL connection is established
(green tick mark in layer-1 box).

The bridge can also be activated directly. If
layer 1 has not yet been established, this is
automatically started as well.



Switches to the layer-1 box and other
elements, see page 76 for explanation.



<Edit>

Bridge/router parameter settings.

<Stop>

Deactivates bridge mode.

<Info>

Displays the activity of bridge
mode.

When the ADSL physical layer is active,
you can run the following tests using the
softkey

<Test>

, see page 98.

No tests are available when
bridge mode is active.

Displays the connection
parameters.

<Info>
or

Displays the VDSL
connection parameters,
see page 47.

<Stop>

Disconnects the VDSL
connection and automatically
deactivates the bridge.

Establishing the VDSL bridge

Summary of Contents for 152

























































































































































































































































































































































































































Search results

Summary of Contents for 152

Reviews:

Related manuals for 152

Brands by name

Popular brands

Argus 152, Manual

Search results

Summary of Contents for 152

Reviews:

Related manuals for 152

Brands by name

Popular brands