Argus 152 Manual Download Page 92

Page: 92 / 408

9 Virtual lines (VL)

ARGUS 152

9.5 Displaying protocol statistics

Continued on
next page

Depending on the access mode and the protocol, ARGUS displays BRAS, IP, PPP, ATM or
Ethernet statistics.



The physical layer, virtual line and



service data are active.



BRAS information:



For PPP protocol only, ARGUS displays
the Broadband Access Server (BRAS)
information:



- AC (access server): name of server



- Service name name of service

<Info>

Displays DSL results.

<Stop>

Deactivates physical layer, VL
and Data service.



Switch to the virtual line (VL) using
the cursor keys.

Press one after
another



and

Display of ARGUS MAC
addresses:



Line, LAN, ETH, see also
page 100 and following.

<IPv4>

Displays the configuration
assigned by the server.

Summary of Contents for 152

























































































































































































































































































































































































































Search results

Summary of Contents for 152

Reviews:

Related manuals for 152

Brands by name

Popular brands

Argus 152, Manual

Search results

Summary of Contents for 152

Reviews:

Related manuals for 152

Brands by name

Popular brands