Argus 152 Manual Download Page 381

Page: 381 / 408

29 Appendix

ARGUS 152

381

“Service or option not implemented,
service or option unspecified, option
not implemented class“ (Dummy)

Unspecified

Invalid call reference value

Identified Channel does not exist

Requested channel is invalid

A suspended call exists, but this call
identity does not

The call identity entered is the wrong one for the parked call

Call identity in use

The call identity is already in use

No call suspended

No call has been parked

Call having the requested call
identity has been cleared

The parked call has been cleared

Incompatible destination

Invalid transit network selection

Invalid format for the transit network identifier

Invalid message, unspecified

Unspecified for "invalid message class" (Dummy)

Mandatory information element is
missing

The mandatory information element is missing

Message type non-existent or not
implemented

This type of message is in this phase not permitted, not
defined or not supported

Message not compatible with call
state or message type non-existent
or not implemented

In this phase, the message is not permitted, not defined or
not supported

Information element non-existent or
not implemented

In this phase, the content of the information element is not
permitted, not defined or not supported

100

Invalid information element contents

Invalid content in information element

101

Message not compatible with call
state

Message not valid in this phase

102

Recovery on timer expired

Error handling routine started due to time-out

111

Protocol error, unspecified

Unspecified for "protocol error class" (Dummy)

127

Interworking, unspecified

Unspecified for "interworking class" (Dummy)

Summary of Contents for 152

























































































































































































































































































































































































































Search results

Summary of Contents for 152

Reviews:

Related manuals for 152

Brands by name

Popular brands

Argus 152, Manual

Search results

Summary of Contents for 152

Reviews:

Related manuals for 152

Brands by name

Popular brands