Argus 152 Manual Download Page 330

Page: 330 / 408

Continuation on
next page

Other result graphs

22 Copper tests

330

ARGUS 152

Display the bit distribution



i. e. transported bits per tone (channel):



y-axis: bits



x-axis: tones (channels)



Display the signal-to-noise-ratio (SNR) per
tone:



y-axis: SNR in dB



x-axis: tones (carrier frequencies)



It is possible to detect disturbances on the
individual tones (channels).



<Menu>

Abort and save

The ARGUS will return to the
previous display

<Menu>

The Graphic functions like
Zoom and Cursor can be
performed in the same
manner as on an xDSL line,
see page 50.

<Continue>

To scroll to the next graphic.

Opens the graphic functions
(see page 50)

Summary of Contents for 152

























































































































































































































































































































































































































Search results

Summary of Contents for 152

Reviews:

Related manuals for 152

Brands by name

Popular brands

Argus 152, Manual

Search results

Summary of Contents for 152

Reviews:

Related manuals for 152

Brands by name

Popular brands