Argus 152 Manual Download Page 14 | Manualshive

Page: 14 / 408

background image

2 Safety information

14

ARGUS 152

16.

If the battery pack fails to charge by the end of the charging time, it can no longer
be recharged.

17.

Do not expose the battery pack to excessive pressure.

18.

If the battery pack emits odours or heat, becomes discoloured or deformed or
otherwise appears different from normal during operation, charging or storage,
immediately remove the battery pack from the device and never use it again.

19.

In the event that acid leaks and comes in contact with eyes or skin, wash
immediately with clean water. Do not rub. In both cases, seek medical attention
immediately. Otherwise, permanent injury may occur.

20.

Keep the battery pack away from children.

21.

Read this manual and the corresponding safety information carefully before using
the battery pack.

22.

If odours, rust or other abnormalities are detected before the first use, contact
intec GmbH to clarify the next steps.

«
...
12
13
14
15
16
...
»

Summary of Contents for 152

























































































































































































































































































































































































































Reviews:

No comments

Related manuals for 152

Brand: 2N Pages: 11

Brand: 2N Pages: 5

Brand: 2N Telekomunikace Pages: 24

Brand: Quick Eagle Networks Pages: 4

Brand: Paradyne Pages: 11

Brand: Paradyne Pages: 19

Brand: Paradyne Pages: 32

COMSPHERE 3550 Series

Brand: Paradyne Pages: 153

Jetstream CPX-1000

Brand: Paradyne Pages: 141

FrameSaver 9783

Brand: Paradyne Pages: 28

COMSPHERE 6800 Series

Brand: Paradyne Pages: 7

Brand: Juniper Pages: 502

Brand: Enginko Pages: 19

RealPort Ethernet 10/100

Brand: Xircom Pages: 30

Brand: Tektronix Pages: 178

DL-DVI-Vision-IP Series

Brand: G&D Pages: 228

BiPAC 5200S RC Series

Brand: Billion Pages: 79

Brand: Hamlet Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands