manualshive.com logo in svg

Argus 152, Manual

Share
Download
Argus 152 Manual Download Page 111

13 ATM tests

ARGUS 152

 

111

13.2 ATM-OAM ping

With an ATM-OAM ping, ARGUS checks the availability of individual ATM nodes or the 
availability of an ATM partial network. OAM stands for Operation, Administration and 
Maintenance and is used to monitor ATM data transmission.

The following parameters must be saved in the profile for the ATM-OAM ping (when the 
ADSL connection is already established, the connection parameters, e.g. ADSL mode and 
target value, are locked):

Protocol-independent parameters:

The opening of test parameters is described in the chapter "Configuring accesses", see 
page 30.

Setting

Description

Test parameters:

ATM-OAM ping

VPI/VCI

Entry of the VPI and VCI for the ATM-OAM ping.

Range: VPI: 0 to 255, VCI: 32 to 65535

Default: 

VPI: 1, VCI: 32

Number of 
pings 

Number of test packets sent by ARGUS. 

When 0 is set ARGUS sends continuously until the ATM-OAM ping 
is halted manually.

Range: 1 to 99999

Default: 

3

 

Timeout

Maximum wait time for the response from the ATM network node to 
the test packet sent by ARGUS.

Range: 0.1 - 9.9 seconds

Default: 

1 second

OAM cell type

F5 loopback segm.: the first ATM node of the virtual channel 
responds to the loopback cell. 

F5 loopback ete: the end point of the virtual channel responds to the 
loopback cell.

Default: 

F5 loopback ete

Summary of Contents for 152

























































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands