manualshive.com logo in svg

Argus 152, Manual

The Kenmore 152 is a versatile and reliable appliance that simplifies your daily chores. To gain full control and maximize its potential, make sure to download the comprehensive Owner's Manual from manualshive.com for free. This handy manual is your go-to resource, offering detailed instructions and tips for optimal product usage.

Share
Download
background image

22 Copper tests

ARGUS 152

 

335

Bandplan

The band plan forms the basis for the measurement evaluation. This 
determines the assignment and the bandwidth of the upstream and 
downstream ranges as well as the PSD mask (max. permissible 
transmission power/tone) required for determining the SNR.

Depending on the bandwidth, you can choose from the following band 
plans:

- Annex A (ADSLx)

- Annex B (ADSLx)

- 998-M2x-A (VDSL2)

- 998-M2x-B (VDSL2)

- 998ADE17-M2x-A (VDSL2)

- 998ADE17-M2x-B (VDSL2)

- 998ADE30-M2x-NUS0-A (V)

- 998ADE30-M2x-NUS0-M (V)

The band plan you require depends on the bandwidth and on the carrier.

Default: 

Annex B (ADSL x)

Impedance

The impedance determines how the line is terminated in the device. Ideally, 
the impedance is selected to be equal to the characteristic impedance of 
the line. 

Possible values are 100 

 (VDSL2), 120 

 and 135 

.

Default: 

135 



(typical for ADSL)

Transmit 
level

The transmit level specifies the level with which the tones of the spectrum 
are sent. The default should be increased only in exceptional cases, as 
otherwise there is the risk of interference to adjacent DSL lines.

Default: 

0 dBm

Summary of Contents for 152

























































































































































































































































































































































































































Reviews:

No comments

Related manuals for 152

D-Link Express Ethernetwork DI-704P Quick Install Manual preview
Express Ethernetwork DI-704P
Brand: D-Link Pages: 17
Stephen STES2026 Configuration Manual Manual preview
STES2026
Brand: Stephen Pages: 102
Macsense MIH-108 User Manual preview
MIH-108
Brand: Macsense Pages: 39
Abocom PLS342 Specification Sheet preview
PLS342
Brand: Abocom Pages: 2
pivotal COMMWARE ECHO 5G How To Set Up preview
COMMWARE ECHO 5G
Brand: pivotal Pages: 2
Paradyne Hotwire 8343 Installation Instructions Manual preview
Hotwire 8343
Brand: Paradyne Pages: 6
LaCie 301300U - Ethernet Disk NAS Server User Manual preview
301300U - Ethernet Disk NAS Server
Brand: LaCie Pages: 62
Softing TH LINK Installation Manual preview
TH LINK
Brand: Softing Pages: 16
Sans Digital Mobileraid MR8X Detailed User'S Manual preview
Mobileraid MR8X
Brand: Sans Digital Pages: 81
PairGain 150-2230-01 Quick Installation Manual preview
150-2230-01
Brand: PairGain Pages: 48
Allynk Technology CAG-0100 User Manual preview
CAG-0100
Brand: Allynk Technology Pages: 39
IBM Turbo 16/4 Token-Ring PC Card 2 User Manual preview
Turbo 16/4 Token-Ring PC Card 2
Brand: IBM Pages: 123
IBEX Westermo Ibex-RT-330-5G Series Manual preview
Westermo Ibex-RT-330-5G Series
Brand: IBEX Pages: 36
ROBOfiber RB-GES401-POE User Manual preview
RB-GES401-POE
Brand: ROBOfiber Pages: 2
Extron electronics RGB 460xi FSR Series Installation Manual preview
RGB 460xi FSR Series
Brand: Extron electronics Pages: 9
Cisco NM-1A-E3 User Manual preview
NM-1A-E3
Brand: Cisco Pages: 26
Cisco Linksys WET610N Quick Installation Manual preview
Linksys WET610N
Brand: Cisco Pages: 78
Cisco MX60 Manual preview
MX60
Brand: Cisco Pages: 8

Brands by name

Popular brands

Load more brands