Argus 152 Manual Download Page 104 | Manualshive

Page: 104 / 408

background image

12 Loop

104

ARGUS 152

TPID

8100 Hex The VLAN TPID 8100 hex is a 16-bit field

that identifies frames according to IEEE
802.1Q (VLAN-tagged frame). It also
makes it possible to use all network paths
actively according to IEEE 802.aq (shortest
path bridging, SPB).

88A8 Hex VLAN TPID 88A8 supports provider bridg-

ing according to IEEE 802.ad. It also
makes it possible to use all network paths
actively according to IEEE 802.aq (shortest
path bridging, SPB).

Default:

8100 Hex

2. VLAN
(S-VLAN)

ID

Identifier for the VLAN to which the frame belongs.
Every VLAN is assigned a unique number, the VLAN
ID. A device that belongs to the VLAN with ID = 2 can
communicate with every other device in the same
VLAN but not with devices in other VLANs.



Range: from 0 to 4095



Default:

2

The IDs 0, 1 and 4095 are reserved for management
purposes and should preferably not be used.

Priority User priority information:



One of eight (3-bit) priorities can be specified for each
frame. This makes it possible e.g. to give priority to
transmitting speech data while treating HTTP data with
lower priority.



Range: 0 to 7



Default:

0

TPID

8100 Hex The VLAN TPID 8100 hex is a 16-bit field

that identifies frames according to IEEE
802.1Q (VLAN-tagged frame). It also
makes it possible to use all network paths
actively according to IEEE 802.aq (shortest
path bridging, SPB).

«
...
102
103
104
105
106
...
»

Summary of Contents for 152

























































































































































































































































































































































































































Reviews:

No comments

Related manuals for 152

Brand: Tripp Lite Pages: 2

Brand: Falcon Pages: 24

Brand: dixell Pages: 4

Brand: Lancom Pages: 70

Brand: Patton electronics Pages: 12

Brand: Asante Pages: 150

Brand: IBM Pages: 34

Network Scanning Unit A

Brand: Ricoh Pages: 206

AirBridge VS-YOFIMN-000

Brand: Vivint Pages: 2

Brand: Ruckus Wireless Pages: 4

Brand: Baileigh Pages: 20

Brand: Paradyne Pages: 10

Brand: Gigabyte Pages: 10

Y.FORCE YTPC400

Brand: YTTEK Pages: 26

Brand: Crestron Pages: 2

Brand: Honeywell Pages: 29

Brand: Honeywell Pages: 60

Wireless Communication Card

Brand: Honeywell Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands