Argus 152 Manual Download Page 36

Page: 36 / 408

7 Operation on xDSL accesses

ARGUS 152

7.1 Configuring the xDSL interface

ARGUS status screen:
Layer-1 box (blue in display) selected.

<Edit>

Opens settings

Status screen

Status screen:

Display (from top to bottom)

- Access mode (in this example: VTU-R)

- Previous profile (in this example: profile 1)

- Modem state (in this example: power down)

- DC voltage on the interface

VDSL test not yet started:

Meaning of LED image in display:

Red LED:

No test started

Yellow LED: Test started

Green LED: Connected

<Menu>

Switches to main menu, see
menu tree

<Status>

Switches to status screen

see page 44

Main menu, see menu tree

Note: accessing functions via number keys/key combinations



You can call important functions/tests directly using the keys of the ARGUS keypad. You
can find an overview of these key combinations on page 98.

Summary of Contents for 152

























































































































































































































































































































































































































Search results

Summary of Contents for 152

Reviews:

Related manuals for 152

Brands by name

Popular brands

Argus 152, Manual

Search results

Summary of Contents for 152

Reviews:

Related manuals for 152

Brands by name

Popular brands