manualshive.com logo in svg

Argus 152, Manual

Share
Download
Argus 152 Manual Download Page 23

5 Configuring accesses

ARGUS 152

 

23

5 Configuring accesses

 Switch on ARGUS.

Continued on 
next page

After powering up, ARGUS displays all 
configured accesses (up to 100). By 
default, one access is preconfigured for 
every interface type (ADSL, VDSL, ...). 

The most recently used access is indi-
cated on the display with  .
ARGUS additionally displays a preview of 
the selected access settings, see also 
page 27. The preview window opens after 

2 seconds.

<New>

<Edit>

With the 

<Filter>

 softkey, ARGUS lets 

you filter all pre-configured accesses 
according to access type (ADSL, VDSL, 
...) and displays this group. 

In this example, VDSL is selected.

All relevant accesses are displayed in 
which VDSL is specified in the confi-

guration.

The status line (above the softkeys) con-
tinues to show the access that is "still" 
selected (in this example VDSL).

<All>

<Edit>

Creates an access, see 
page 24, Fig. 2.

Edits an access, see page 24, 
Fig. 1.

Toggles softkey assignment, 
see page 28.

Switches to main menu.

Display of all possible 
accesses, see Fig. 1.

Edits the selected access 
profile.

Summary of Contents for 152

























































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands