Argus 152 Manual Download Page 198 | Manualshive

Page: 198 / 408

background image

17 Parallel tests

198

ARGUS 152

17 Parallel tests

ARGUS permits parallel testing of different IP-based services (Data, VoIP, IPTV and VoD)
running on xDSL or Ethernet interfaces.
The settings for each test are described in the respective chapters.

The following tests can be run in parallel. Any combination of the tests listed here is



possible.

Service

Test

Remark

Data

IP ping*

1

For theses tests, up to 10 tests can be
conducted concurrently (incl. tests
using the other services).

Traceroute*

1

HTTP download, see page 124

FTP download, see page 131

FTP upload, see page 133

FTP server, see page 137

See remark for VoIP.

VoIP

VoIP call, see page 144

These tests can be combined with
any other test. Note that only one
VoIP test can be active at any time.

VoIP wait, see page 162.

VoIP PESQ test, see page 284

IPTV

IPTV, see page 164

These tests can be combined with
any other test. Note that only one
IPTV test can be active at any time.

IPTV scan, see page 179

IPTV passive, see page 186

VoD

VoD, see page 190

See remark for IPTV

*

1

Also possible via the services VoIP, IPTV and VoD.

«
...
196
197
198
199
200
...
»

Summary of Contents for 152

























































































































































































































































































































































































































Reviews:

No comments

Related manuals for 152

Ray 3 Plus Client

Brand: Sun Microsystems Pages: 6

HomePlug AV Ethernet Bridge PLE0200

Brand: Abocom Pages: 2

Brand: Telex Communications Pages: 28

NVIP- NVRA0104/GO

Brand: Novus Pages: 44

SUPERLOADER DLT MAGAZINE

Brand: Tandberg Data Pages: 6

Brand: Eicon Networks Pages: 32

Enterasys Matrix 2G4082-25

Brand: Enterasys Pages: 58

Brand: BWI Pages: 5

EtherLink 3C905C-TX

Brand: 3Com Pages: 96

Brand: Intercoax Pages: 2

PG-Flex FLC-704

Brand: PairGain Pages: 20

Elinx EIR510 Series

Brand: B&B Electronics Pages: 2

Brand: Casablanca Pages: 13

IP-Logic ZIG-IPPRO-RX

Brand: Zigen Pages: 4

NetCon FBR-1409TX

Brand: LevelOne Pages: 88

Brand: 2N Telekomunikace Pages: 67

Brand: LaView Pages: 2

Dynalink MyZone 3G24W

Brand: NetComm Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands