Argus 152 Manual Download Page 11 | Manualshive

Page: 11 / 408

background image

2 Safety information

ARGUS 152

11

2 Safety information

ARGUS may only be operated using the accessories supplied with the device. The use of
other accessories can result in faulty measurements or even damage to ARGUS and the
connected equipment. Only use ARGUS according to the instructions contained in this
accompanying document. Use in any other manner can cause harm to persons or destroy
your ARGUS.

-

Before connecting ARGUS to an access, make sure that no dangerous
voltages or voltages for which ARGUS and its accessories are not specified
are present. Also keep in mind that the voltage can change over the time that
the device is connected.

-

Use ARGUS only according to its intended purpose at all interfaces and local
loops.

-

Voltages over 50 V AC and 120 V DC can cause death.

-

Never conduct measurements without the battery pack!

-

ARGUS is not waterproof. Therefore, protect ARGUS against water
penetration.

-

Before replacing the battery pack, disconnect the power adapter and all
measuring leads and power ARGUS down.



ATTENTION: Never remove the battery pack during operation.

-

Remove the power adapter from the mains socket as soon as ARGUS is
switched off or no longer in use (e.g.after charging the battery pack)!

-

ARGUS may only be used by trained personnel.

-

ARGUS may only be operated using the power adapter supplied with the
device.

-

Only manufacturer-approved headsets may be connected to the headset
socket; any other use of this socket (e.g. connection to a home entertainment
system) is expressly prohibited.

-

Only the Active Probe II, the ARGUS Copper Box and the other
manufacturer-approved USB devices without mains connection may be
connected to the USB host interface (USB-A). Any other use (e.g. connection
to a PC) is expressly prohibited.

-

If external USB devices are used on the USB-host interface (USB-A), no
warranty is assumed for occurrences outside the mechanical wear of normal
plug-in.

-

In battery power mode, always cover the ARGUS power socket with the
supplied rubber protective cap labelled "Power".

-

The electromagnetic compatibility (EMC) has been tested according to the
regulations specified in our conformity declaration.



ARGUS is a class A device. This device can cause radio interference in
residential areas. In this case, the user may be required to implement
appropriate measures.

«
...
9
10
11
12
13
...
»

Summary of Contents for 152

























































































































































































































































































































































































































Reviews:

No comments

Related manuals for 152

Brand: A-Link Pages: 6

Brand: F5 Pages: 2

Brand: F5 Pages: 90

Brand: F5 Pages: 47

Brand: H3C Pages: 33

S5500-SI Series

Brand: H3C Pages: 1217

Brand: 3Com Pages: 2443

Brand: H3C Pages: 3

Brand: H3C Pages: 4

Brand: Quick Eagle Networks Pages: 4

3C410012A - OfficeConnect Remote 531 Access...

Brand: 3Com Pages: 72

Brand: TP-Link Pages: 2

Brand: Black Box Pages: 37

PoleVault System A/V Source Inputs

Brand: Extron electronics Pages: 4

Brand: 3Com Pages: 50

FlexNetwork 5130 Series

Brand: HPE Pages: 33

Brand: Ubiquiti Pages: 23

Brand: ACTi Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands