Argus 152 Manual Download Page 74

Page: 74 / 408

<Statistic>

page 73

8 Operation with Ethernet accesses

ARGUS 152

Displays polling and offset between wires



Statistic display



Disconnecting from the Ethernet connection and saving the results

You can disconnect and save the results from an Ethernet connection as described for
VDSL, see page 63.

Saving the results without disconnecting from the Ethernet connection

You can save your results for an Ethernet connection without disconnecting in the same
way as for VDSL, see page 64.

- Wire allocation

Left column

ARGUS wire allocation

Right column ARGUS wire allocation after

autonegotiation with remote
terminal. When the display
shows "OK", the remote
station has inverted the wire
allocation.

- Polling

- Skew in ns

Received (Rx) and transmitted (Tx)
internet frames

Received (Rx) and transmitted (Tx)
bytes

Number of errors on the receiver (Rx)
and transmitter (Tx) side

Number of collisions

Summary of Contents for 152

























































































































































































































































































































































































































Search results

Summary of Contents for 152

Reviews:

Related manuals for 152

Brands by name

Popular brands

Argus 152, Manual

Search results

Summary of Contents for 152

Reviews:

Related manuals for 152

Brands by name

Popular brands