Argus 152 Manual Download Page 4

Page: 4 / 408

ARGUS

ARGUS 152

IP tests .............................................................................................114

14.1

IP ping ..............................................................................................114

14.2

Traceroute .......................................................................................120

14.3

HTTP download ...............................................................................124

14.4

FTP download .................................................................................129

14.5

FTP upload ......................................................................................133

14.6

FTP server .......................................................................................137

VoIP tests ........................................................................................144

15.1

Starting VoIP telephony .................................................................152

15.1.1 VoIP back-to-back .................................................................160

15.2

VoIP wait ..........................................................................................161

IPTV tests ........................................................................................164

16.1

IPTV ..................................................................................................164

16.1.1 Multiple virtual lines ...............................................................168

16.2

IPTV scan .........................................................................................179

16.3

IPTV passive ....................................................................................186

16.4

Video on demand (VoD) .................................................................190

Parallel tests ....................................................................................198

Auto tests ........................................................................................204

Operation on an ISDN Access .......................................................208

19.1

Setting the ISDN Interface and Access Mode ..............................208

19.2

Initialization phase followed by a B channel Test .......................209

19.3

ISDN Settings ..................................................................................212

19.4

Bit Error Rate Test ..........................................................................216

19.5

Supplementary Services Test ........................................................226

19.6

Service check ..................................................................................230

19.7

X.31 Test ..........................................................................................232

19.8

Call Forwarding (CF) ......................................................................240

19.9

Automatic Performance of Multiple Tests ....................................244



Summary of Contents for 152

























































































































































































































































































































































































































Search results

Summary of Contents for 152

Reviews:

Related manuals for 152

Brands by name

Popular brands

Argus 152, Manual

Search results

Summary of Contents for 152

Reviews:

Related manuals for 152

Brands by name

Popular brands