Argus 152 Manual Download Page 128

Page: 128 / 408

14 IP tests

128

ARGUS 152

Display of test status:



You can observe the running test or start a
new test here, see page 198.



Display of results:



Exits results.



Saves HTTP download result, see
page 118.



Sends trace file to PC, see page 91

<New>

Selects a new single test.

<Stop>

Stops HTTP download test.

Displays test status without
ending the test or starting a
new test, see page 198.

<New>

Starts a new HTTP download.

Calculated average speed of all downloads
(in this example 72,691 Mbit/s).

Transferred file size



(in this example 485,750 MB).

Average time required for a download in
h:min:s.

Maximum parallel downloads.

Configured parallel downloads.

HTTP download result

Save result?

Summary of Contents for 152

























































































































































































































































































































































































































Search results

Summary of Contents for 152

Reviews:

Related manuals for 152

Brands by name

Popular brands

Argus 152, Manual

Search results

Summary of Contents for 152

Reviews:

Related manuals for 152

Brands by name

Popular brands