manualshive.com logo in svg

Argus 152, Manual

The Kenmore 152 is a versatile and reliable appliance that simplifies your daily chores. To gain full control and maximize its potential, make sure to download the comprehensive Owner's Manual from manualshive.com for free. This handy manual is your go-to resource, offering detailed instructions and tips for optimal product usage.

Share
Download
background image

23 Ethernet cable tests

ARGUS 152

 

341

23.3 Ethernet cable test 

The Ethernet cable test checks for faults in LAN cabling. ARGUS interprets the 
measurement result and determines whether this indicates an open line, a short-circuit or a 
mismatch.

23.3.1 Starting Ethernet cable test

<Setting>

<Menu>

<Start>

ARGUS in the status line.

Select one of the Ethernet tests:
- ETH TDR/cable test
- ETH port flash

Start the desired Ethernet test directly by 
selecting it.
In this example, this is the ETH/TDR cable 
test.

The Ethernet TDR/cable test is executed.

Opens the Ethernet cable test 
settings, see page 340.

Opens the main menu.

Starts Ethernet cable test.

The Ethernet TDR should always 
be measured at both ends of the 
cable. This reveals e.g. contact 
problems at the remote line end in 
the second, twisted test, as this 
type of fault can not be 
distinguished from the line end. 

  

 

Summary of Contents for 152

























































































































































































































































































































































































































Reviews:

No comments

Related manuals for 152

ZETR 25 Installation Manual preview
25
Brand: ZETR Pages: 2
CallDirect CD Series At Command Manual preview
CD Series
Brand: CallDirect Pages: 33
IBM 3708 Description preview
3708
Brand: IBM Pages: 342
Vivotek NR8401 User Manual preview
NR8401
Brand: Vivotek Pages: 136
TFortis Teleport-1 Configuration Manual preview
Teleport-1
Brand: TFortis Pages: 86
process-informatik CONNECT Series Operation Quick Start Manual preview
CONNECT Series
Brand: process-informatik Pages: 8
IDT Tsi310TM User Manual preview
Tsi310TM
Brand: IDT Pages: 207
Quantum QWCM Installation Manual preview
QWCM
Brand: Quantum Pages: 7
Leviton IPHS5-1LW Product Bulletin preview
IPHS5-1LW
Brand: Leviton Pages: 4
MSNswitch UIS-322b Quick Installation Manual preview
UIS-322b
Brand: MSNswitch Pages: 2
SONIX MP5S Plus Writer Quick Manual preview
MP5S Plus Writer
Brand: SONIX Pages: 23
LevelOne FBR-1412TX User Manual preview
FBR-1412TX
Brand: LevelOne Pages: 83
NetComm RTA100 User Manual preview
RTA100
Brand: NetComm Pages: 75
Proscend 6200-2W User Manual preview
6200-2W
Brand: Proscend Pages: 93
Teltonika RUT955 User Manual preview
RUT955
Brand: Teltonika Pages: 12
PairGain T1L2F10A Manual preview
T1L2F10A
Brand: PairGain Pages: 76
NetComm Wireless NTC-140-01 User Manual preview
NTC-140-01
Brand: NetComm Wireless Pages: 154
Riverbed Cascade Express Installation Manual preview
Cascade Express
Brand: Riverbed Pages: 92

Brands by name

Popular brands

Load more brands