Argus 152 Manual Download Page 255

Page: 255 / 408

19 Operation on an ISDN Access

ARGUS 152

255



Other causes are not shown in clear text, rather as decimal codes (see ”ARGUS Error
Messages (DSS1)" on page 382).

Call reject

The call is actively rejected

Wrong number

Wrong call number format or call number is
incomplete

Norm. clearing

Unspecified “normal class” (Dummy)

No B chan.avail.

No circuit / B channel available

Req.chan.unavail

Requested B channel not available

Req.fac.not subs

Requested supplementary service (facility) not
subscribed

BC not authoriz.

Requested bearer capability is not enabled

Srv./opt.n.avail

Unspecified for “Service not available” or “Option not
available”

Req.fac.not impl.

Requested facility is not supported

Incompat. Dest.

Incompatible destination

102

Timer expired

Error handling routine started due to time-out

111

Protocol error

Unspecified for “protocol error class”

127

Interworking err

Unspecified for “interworking class”

Summary of Contents for 152

























































































































































































































































































































































































































Search results

Summary of Contents for 152

Reviews:

Related manuals for 152

Brands by name

Popular brands

Argus 152, Manual

Search results

Summary of Contents for 152

Reviews:

Related manuals for 152

Brands by name

Popular brands