Argus 152 Manual Download Page 202

Page: 202 / 408

17 Parallel tests

202

ARGUS 152

The called subscriber has taken the call
("Connected!"), see page 153.



ARGUS executes an HTTP download and
a VoIP call in parallel.

The VoIP call is stopped.

<Info>

Displays the VoIP parameters.

<Volume>

Opens volume control.

When more than one test is
executed, you can select the tests
with the left and right cursor keys.



For more than three tests, the test
row expands to the right.

<New>

Selects a new single test.

<Stop>

Stops the test, in this example VoIP
call. Depending on the test, it can
be reinitialised using

<Start>

. The

configuration remains unchanged.

Stops all tests.

Toggles the softkey assignment.

To start a new VoIP call test, the old
one must be cleared by pressing

twice.

or Switches to the test result

parameters, in this example from
HTTP download.

<New>

Selects a new single test.

<Stop>

Stops the test.

Summary of Contents for 152

























































































































































































































































































































































































































Search results

Summary of Contents for 152

Reviews:

Brands by name

Popular brands

Argus 152, Manual

Search results

Summary of Contents for 152

Reviews:

Brands by name

Popular brands