manualshive.com logo in svg

Argus 152, Manual

Share
Download
Argus 152 Manual Download Page 149

15 VoIP tests

ARGUS 152

 

149

Phone 

settings

(continued)

Codecs

Prepares a list of the speech codecs to be used. For 
multiple codecs, the order determines the priority.

Switches to softkey assignment.

<

>

The selected codec is moved down one 
place in the list.

<

>

The selected codec is moved up one 
place in the list.

<Insert>

A display with the available voice 
codecs opens. A voice codec marked 

with 

 in this selection menu is 

inserted in the voice codec list (via the 
voice codec marked in the list).

<Delete>

Deletes the marked codec from the list.

Adopts the codec priorities.

Supported 
Codecs

G.729 A/B, G.726-40, G.726-32, 

G.726-24, G.726-16, G.722, G.711 A law, 
G.711 

μ

 law, G.723.1

DTMF

settings

Dual-tone multi-frequency (DTMF) is a multifrequency 
dialling method.

Mode: Sets DTMF mode

You can choose between "Automatic", "SIP info", "RFC 
2833" and "Inband".

Default: 

Automatic

Duration: Sets the VoIP DTMF timer

Range: 40 to 1000 ms.

Up to 200 ms in steps of 10, up to 300 ms in steps of 
20, up to 1000 ms in steps of 100. 

Default: 

80 ms

 

 Increases or decreases the VoIP DTMF duration.

Summary of Contents for 152

























































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands