manualshive.com logo in svg

Argus 152, Manual

Share
Download
Argus 152 Manual Download Page 120

14 IP tests

120

ARGUS 152

14.2 Traceroute

In IP traceroute, ARGUS sends test packets and displays all hops and their response times 
on the way to the destination address. This data enables precise localisation of possible 
delays in the network.

The following parameters must be saved in the profile for the IP traceroute:

Protocol-independent parameters:

The opening of test parameters is described in the chapter "Configuring accesses", see 
page 30.

Setting

Description

Test parameters:

Traceroute:

IP address

The IP address of a destination node can be entered as either an IP 
number or a name (URL), see IP ping/IP address for instructions, 
page 115.

Default: 

www.argus.info

Maximum hops

Maximum number of hops over which the path to the destination 
address node is tracked.

Range: 1 to 25

Default: 

25

Probes

Number of attempts to address a network node.

Range: 1 to 10

Default: 

3

 

Timeout

Maximum wait time for the response of a network node.

Range: 0.05 - 9.9 seconds

Default: 

3 seconds

Summary of Contents for 152

























































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands