Argus 152 Manual Download Page 118

Page: 118 / 408

14 IP tests

118

ARGUS 152

ARGUS displays the results when the test
is finished:



Display of test status:



You can observe the running test or start a
new test here, see page 198.

- Number of packets sent

- Number of packets received

- Number of packets repeated

- Checksum errors

- Number of packets received with error

- Minimum packet response time in ms

- Maximum packet response time in ms

- Average packet response time in ms

<Desti-
nation
address>

Displays the URL and the IP
address.

Displays test status without
ending the test or starting a new
test, see page 198.

<New>

Starts a new IP ping test.

<New>

Selects a new single test.

<Start>

Starts a new IP ping test.

Continued on
next page

IP ping result

Summary of Contents for 152

























































































































































































































































































































































































































Search results

Summary of Contents for 152

Reviews:

Related manuals for 152

Brands by name

Popular brands

Argus 152, Manual

Search results

Summary of Contents for 152

Reviews:

Related manuals for 152

Brands by name

Popular brands