Argus 152 Manual Download Page 73

Page: 73 / 408

8 Operation with Ethernet accesses

ARGUS 152

8.3 Establishing an Ethernet connection

Establishing an Ethernet



connection

ARGUS in the status screen.



ARGUS uses the default profile (profile 1
in the example) to establish an Ethernet
connection.

Meaning of the arrow in the layer-1 box

Gray arrow

Yellow arrow

Green check
mark

The test has not yet started!

no test started

test started

connected



<Info>

Displays Ethernet connection
parameters.

<Stop>

Stops the Ethernet connection.



Display:

- Autonegotiation setting

- Autoneg. at remote station

- Negotiated speed

- Type of duplex mode

- Flow control setting



<Statistic>

Opens Ethernet statistics

Summary of Contents for 152

























































































































































































































































































































































































































Search results

Summary of Contents for 152

Reviews:

Related manuals for 152

Brands by name

Popular brands

Argus 152, Manual

Search results

Summary of Contents for 152

Reviews:

Related manuals for 152

Brands by name

Popular brands