Argus 152 Manual Download Page 43 | Manualshive

Page: 43 / 408

background image

7 Operation on xDSL accesses

43

ARGUS 152

7.3 ARGUS in access mode xTU-R

Determining the xDSL connection parameters using VDSL as an example



(procedures also apply for ADSL connections)

ARGUS is connected directly to the VDSL access via the supplied xDSL lead and the
ARGUS socket line (either in front of or behind the splitter). In this case, ARGUS replaces
the modem and PC. ARGUS establishes a VDSL connection and determines all relevant
VDSL connection parameters. ARGUS displays the VDSL connection parameters and, if
desired, saves them when the link is disconnected.

Use only the patch cable supplied with the device.



In this example, VDSL VTU-R mode is configured and selected as described in chapter „5
Configuring accesses“ (see page 23).



socket



Line

VDSL access



VTU-C (DSLAM)

xDSL cable or patch cable

The VDSL test has not yet been
started: red LED in the display!



Meaning of LED image in display:



Red LED:

no test started

Yellow LED: test started

Green LED: connected

All further functions and
procedures are explained using
this status screen.

«
...
41
42
43
44
45
...
»

Summary of Contents for 152

























































































































































































































































































































































































































Reviews:

No comments

Related manuals for 152

Brand: ZETR Pages: 2

Brand: CallDirect Pages: 33

Brand: C&H Technologies Pages: 46

Brand: Xantrex Pages: 8

Brand: Campbell Pages: 42

Brand: NETGEAR Pages: 2

TE100-S16 - 10/100Mbps Ethernet Switch

Brand: TRENDnet Pages: 15

Brand: CyberTAN Pages: 67

Brand: ZoneVu Pages: 15

Wisenet XRN-6410RB2-24TB

Brand: Hanwha Techwin Pages: 124

Brand: Idis Pages: 18

Brand: Alcatel-Lucent Pages: 12

Brand: ADTRAN Pages: 136

ipRocketLink 3101 Series

Brand: Patton Pages: 119

Brand: BinTec Pages: 2

Xtreme Networked Boat

Brand: Broadband Products Pages: 16

ClareVision CV-M161620-04

Brand: Clare Controls Pages: 32

SmartNode 4634 Series

Brand: Patton electronics Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands