manualshive.com logo in svg

Analog Devices Blackfin ADSP-BF537, Hardware Reference Manual

The Analog Devices Blackfin ADSP-BF537 is a cutting-edge processor renowned for its exceptional performance and versatility. Unlock the full potential of this remarkable hardware by downloading the comprehensive and free Hardware Reference Manual from our website. All the information you need is just a click away.

Share
Download
background image

SPORT Registers

12-52

ADSP-BF537 Blackfin Processor Hardware Reference

 

SPORTx_TX

 register on time. If the receiver can tolerate occasional 

late frame sync pulses, 

DITFS

 should be cleared to prevent the 

SPORT from transmitting old data twice or transmitting garbled 
data if the processor is late in loading the 

SPORTx_TX

 register.

•

Low transmit frame sync select

. (

LTFS

). This bit selects an active 

low 

TFS

 (if set) or active high 

TFS

 (if cleared).

•

Late transmit frame sync

. (

LATFS

). This bit configures late frame 

syncs (if set) or early frame syncs (if cleared).

•

Clock drive/sample edge select

. (

TCKFE

). This bit selects which 

edge of the 

TCLKx

 signal the SPORT uses for driving data, for driv-

ing internally generated frame syncs, and for sampling externally 
generated frame syncs. If set, data and internally generated frame 
syncs are driven on the falling edge, and externally generated frame 
syncs are sampled on the rising edge. If cleared, data and internally 
generated frame syncs are driven on the rising edge, and externally 
generated frame syncs are sampled on the falling edge.

•

TxSec enable

. (

TXSE

). This bit enables the transmit secondary side 

of the SPORT (if set).

•

Stereo serial enable

. (

TSFSE

). This bit enables the stereo serial oper-

ating mode of the SPORT (if set). By default this bit is cleared, 
enabling normal clocking and frame sync.

•

Left/Right order

. (

TRFST

). If this bit is set, the right channel is 

transmitted first in stereo serial operating mode. By default this bit 
is cleared, and the left channel is transmitted first.

SPORTx_RCR1 and SPORTx_RCR2 Registers

The main control registers for the receive portion of each SPORT are the 
receive configuration registers, 

SPORTx_RCR1

 and 

SPORTx_RCR2

, shown in 

Figure 12-27

 and 

Figure 12-28

.

Summary of Contents for Blackfin ADSP-BF537



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Blackfin ADSP-BF537

PaloAlto Networks PA-5400 Series Quick Start Manual preview
PA-5400 Series
Brand: PaloAlto Networks Pages: 2
VMIC VMICPCI-7755 Product Manual preview
VMICPCI-7755
Brand: VMIC Pages: 126
National Instruments PCI-6110E/6111E User Manual preview
PCI-6110E/6111E
Brand: National Instruments Pages: 113
Daedalon EC-33 Instruction Manual preview
EC-33
Brand: Daedalon Pages: 6
Nortel BayStack 660 Use Manual preview
BayStack 660
Brand: Nortel Pages: 163
Baracoda Scan Dongle User Manual preview
Scan Dongle
Brand: Baracoda Pages: 16
CAME 848EA-0120 Setup And User'S Manual preview
848EA-0120
Brand: CAME Pages: 32
Congatec COM Express conga-TC87 User Manual preview
COM Express conga-TC87
Brand: Congatec Pages: 114
Ebyte ECAN-W01 User Manual preview
ECAN-W01
Brand: Ebyte Pages: 23
MCT MPU100ZW User Manual preview
MPU100ZW
Brand: MCT Pages: 12
ICP GDT6618RD Addendum preview
GDT6618RD
Brand: ICP Pages: 111
AG AstroPC PRO User Manual preview
AstroPC PRO
Brand: AG Pages: 10
X-Micro XWL-11GPAR User Manual preview
XWL-11GPAR
Brand: X-Micro Pages: 24
I-Tech NW117HD-8Ke User Manual preview
NW117HD-8Ke
Brand: I-Tech Pages: 6
Aaeon PER-C41L Quick Installation Manual preview
PER-C41L
Brand: Aaeon Pages: 22
AA WIRELESS AAWireless-002 User Manual preview
AAWireless-002
Brand: AA WIRELESS Pages: 55
HeimVision HM243 User Manual preview
HM243
Brand: HeimVision Pages: 167
Costar CR4020XDI Installation Manual preview
CR4020XDI
Brand: Costar Pages: 24

Brands by name

Popular brands

Load more brands